From: Florida code review (AI)

# Florida residential pool review basis

Review date: September 7, 2026. Collection: `florida-replacement-2026-09-06`, designs 101-120. This is a research and design-review checklist, not a signed engineering assessment or permit approval. It does not report that revised geometry has passed; the independent geometry audit must supply that evidence.

## Applicable edition and evidence limits

Use the Florida Building Code, **8th Edition (2023)** as the current statewide baseline. Its effective date was December 31, 2023. Sarasota County still identifies that edition and **2020 NEC** as its current codes. The Commission's June 2026 workplan schedules the ninth edition for December 31, 2026; recheck the actual permit date and AHJ before releasing construction documents. [Florida Building Commission](https://www.floridabuilding.org/c/Default.aspx), [Sarasota County current codes](https://www.scgov.net/government/planning-and-development-services/building), [Commission June 2026 workplan](https://www.floridabuilding.org/fbc/commission/FBC_0626/Commission/2026_FBC_Workplan_June_2026.pdf).

The official 2023 Residential Chapter 46 index identifies APSP 3-2014 (permanent spas), APSP 5-2012(R2022) (residential inground pools), and PHTA 7-2020 (suction entrapment), referenced by R4501.6.1/.6.3/.6.6. The publisher markets the residential standard as APSP 5-2011(R2022), incorporating the 2012 addendum; resolve the exact adopted text with the designer instead of silently substituting a newer edition. [ICC adopted reference list](https://codes.iccsafe.org/content/FLRC2023P1/chapter-46-referenced-nbsp-standards), [ICC standard identification and access](https://codes-conv.iccsafe.org/content/PHTA5112022P1_U).

The official ICC Chapter 45 and Energy Chapter 4 endpoints returned access errors during this run. The full APSP 5 standard requires subscription access. The earlier September 5 project review records a direct read of the current Florida chapter; its section references are retained below as review targets, with current corroboration where available. **A full clause-by-clause reread of the adopted standards and current supplements remains open.** Do not turn these targets into an automatic “code compliant” badge.

Only private residential use is assumed. Public, shared commercial, hotel/apartment and some rental uses require a separate occupancy review. The federal VGB installation requirements for public pools must not be misrepresented as the complete private-pool rule; Florida's adopted suction standard still governs these designs. Drain-cover products themselves also have federal compliance requirements. [CPSC drain-cover guidance](https://www.cpsc.gov/Business--Manufacturing/Business-Education/Business-Guidance/Pool-and-Spa-Drain-Covers).

## Geometry requirements to implement now

| Topic and section target | Required model action and engineering gate |
|---|---|
| Depth, R4501.2 | Measure depth from finished underwater surface to operating waterline. Store coping elevation/freeboard separately. A “4.5 ft” floor must actually be 54 in below the water surface. Report shelf and seat depths independently. Use net volume after shelf, step and bench displacement for later hydraulics. |
| Pool access, R4501.18; adopted APSP 5 section 6 | Every current design exceeds 24 in and needs entry/exit. Build a continuous usable route from deck to floor; three decorative blocks followed by a large drop fail design sense. Use conservative project targets of **maximum 10 in uniform risers, 12 in clear tread depth, and 36 in clear width**, checking the first rise from coping and the last rise to the floor. Clipping to a curve must not remove the usable tread. These targets exceed the publicly corroborated 10 in / 240 sq in tread minimum and avoid the 12 in maximum-riser limit described in ICC's APSP-correlated material. Final adopted-standard exceptions still need review. [ICC entry guidance](https://www.iccsafe.org/building-safety-journal/bsj-technical/codenotes-permanent-inground-residential-swimming-pool-entry-exit-requirements/), [ICC APSP-correlated stair proposal](https://cdn-www-v2.iccsafe.org/wp-content/uploads/ISPSC1.pdf). |
| Ledges and benches, APSP 5 sections 5-6 | A 9 in-deep tanning ledge cannot replace steps to a 54 in floor. Keep a full clear route around loungers. Use an 18 in-deep social seat as a comfort target, with contrasting edges and no isolated tiny ledges. Seat/ledge exceptions, slip resistance and any handhold requirements need full-standard review. No diving equipment is appropriate for the current uniform 4.5 ft concepts. |
| Permanent spas, R4501.6.1 / APSP 3-2014 | All 11 spas need usable interior steps, seats, footwell, suction fittings and jets. Raised spas also need an exterior approach and landing; do not require climbing a coping wall. Proposed modeling targets: 36 in water depth, coping 6 in above water, four equal 10.5 in interior risers over the 42 in coping-to-floor height, three 12 in treads with 36 in clear width, and first tread 4.5 in below water. The spa riser target is below 12 in and is separate from the pool flight's conservative 10 in maximum. With a 7 ft spa and 3 ft stair run, verify the modeled unobstructed 4 ft footwell and bench extents; 8 in suction covers at 4 ft diagonal centers can fit within a true 4 by 4 ft clear area. A coping 18 in above the surrounding deck uses three exterior 6 in risers, a 36 in landing/approach, and a handrail. Seat immersion target is 18 in. These are explicit project criteria, **not a verified complete APSP 3 specification**. Recheck entry/seat/footwell/handrail details against the licensed standard and selected fittings. |
| Suction, R4501.6.6 / PHTA 7-2020 | Provide distinct pool and spa suction designs. For the illustrated dual-outlet option, place 8 in covers at **4 ft centers**, and connect both branches before any isolating valve. This leaves 40 in between cover edges. The example Pentair manual contains a 3 ft nearest-point warning as well as a 3 ft center-spacing diagram, so 3.2 ft centers is not a robust universal assumption. Spacing alone is insufficient: cover plus sump compatibility, service life, permitted flow, blockage cases, and every pump/valve mode remain unresolved. Generic display covers are not selected listed assemblies. [Pentair MAX-E-PRO instructions, pages ii and 2](https://www.pentair.com/content/dam/extranet/nam/pentair-pool/residential/pumps/max-e-pro/manuals/max-e-pro-pool-pump-manual-english.pdf). |
| Returns/skimmers, R4501.21.2/.21.5 | Baseline planning counts: at least `ceil(water area / 300)` required returns; separate required returns by at least 10 ft shortest distance. At least one skimmer per 800 sq ft or fraction, with at least 25 gpm rated flow. All current main pools are below 800 sq ft. Count actual submerged water area, not the bounding rectangle. Orient returns to sweep recesses and skimmers; count alone does not prove circulation. These references are corroborated by the Commission's historical training and require current-printing confirmation. [Commission pool training](https://floridabuilding.org/fbc/commission/FBC_1015/commission_Education_POC/220/220-3-MATERIAL.pdf). |
| Barriers, R4501.17; F.S. 515.29 | The barrier route must close around the pool, with a documented house-access solution where applicable. Baseline geometry: at least 48 in exterior height, bottom clearance at most 2 in, no 4 in sphere passage, and no climbable arrangements. Use a 60 in project fence with 1.5 in bottom gap and 3.5 in clear picket gaps for tolerance. Where horizontal rail tops are less than 45 in apart, use pool-side rails and at most 1.75 in vertical openings; a 3.5 in picket design therefore needs rail spacing at least 45 in. The detailed rail rule is a current-printing recheck target. [Florida statute 515.29](https://www.flsenate.gov/Laws/Statutes/2026/515.29), [Punta Gorda 2023-code barrier checklist](https://www.ci.punta-gorda.fl.us/home/showpublisheddocument/17094/639150378515430000). |
| Gates/screens, R4501.17.1.8/.9/.11 | Model an outward-opening self-closing/self-latching gate, protected release and complete enclosure continuity. A cage is only a barrier if its entire assembly meets the barrier requirements; screen framing alone proves nothing. Model latch at least 54 in above gate bottom and a solid guard extending 18 in around its release as a conservative project detail. Keep planters, equipment and furniture away from climb routes. Hardware operation, screen strength, foundations and wind loads require product/field review. House doors/windows must follow the chosen approved protection option. [F.S. 515.27 safety options](https://www.flsenate.gov/Laws/Statutes/2026/515.27). |
| Infinity edge / Bayline Edge | Model the real 36 ft weir, a continuous catch basin, basin service/escape access, waterproof structure and separate circulation path. Keep deck/soil out of the basin volume. Engineer run-back/surge capacity, overflow route, low-water protection, suction, exposed drop and barrier strategy. A waterfront backdrop is not an approved natural barrier. PHTA 5-2025 adds catch-basin egress provisions, but its publication does not establish adoption in current Florida law. Treat it as an additional design review, not retroactive adopted text. [PHTA 5-2025 publisher description](https://portal.phta.org/Store/Product-Catalog/Product-Details?productid=%7B2D542EF0-F067-F011-BEC2-6045BD0356C1%7D). |

## Engineering and construction gates still required

### Access-rail correction review, September 7

The first rendered generation exposed access defects missed by the original geometry checks: low or wall-embedded pool rails, unsupported spa rail ends, disconnected catch-basin ladder rungs, and a round-spa landing that touched curved coping only at its center. Those render hashes cannot serve as evidence that the corrected access geometry passed.

As an independently published comparison, **2024 ISPSC §§324.2.1-.5** specify residential grip tops 30-38 in above nosings, 1.25-2 in outside diameter, corrosion resistance, tool-secured installation, and a leading edge within 18 in of the bottom riser. **§§323.3-.3.2** specify slip-resistant ladder treads at least 2 in deep, uniform 7-12 in spacing, a top tread within 12 in of deck/coping, 3-4 in wall clearance, and two rails/handholds with 17-24 in clear spacing. This comparison is **not a finding that Florida adopted the 2024 ISPSC**; the full currently adopted APSP clauses remain an explicit release gate. [ICC 2024 ISPSC, Chapter 3](https://codes.iccsafe.org/content/ISPSC2024P1/chapter-3-general-compliance).

The correction therefore targets a **34 in top-of-grip height**, a 1.5 in tube, and a 12 in lower extension. Its centerline is 33.25 in above the reference surface. Verify the actual nosing pitch, flat landings, shelf turns, end returns, and support positions. Keep a full 36 in unobstructed walking band and a 1.5 in gripping clearance to adjacent fixed surfaces as project criteria. A rail cannot pass merely because its endpoints have suitable elevations: the whole usable route and tube envelope must clear the shell, coping, furniture and stair route.

Deck sockets must reach modeled structural support below pavers and bedding; underwater sockets require a local structural detail, avoiding an assumption that an anchor is suitable in the nominal 6 in shell. S.R. Smith's installation guide calls for the anchor to finish flush with the deck, bonding per applicable electrical rules, and product-specific concrete/installation details. Final rail SKU, bend radius, loading, socket embedment, reinforcing, corrosion compatibility and bonding still require designer and product approval. [S.R. Smith rail installation guide](https://www.srsmith.com/media/126979/rail-installation-guide-10_2017-lr.pdf).

The catch-basin concept correction uses two connected 20 in-center rails (18.5 in clear), four flat 2.5 in-deep treads, and five equal 9 in rises over the 45 in deck-to-floor height, with returned deck grips and supported lower ends. The round-spa landing must overlap the actual outer-coping chord across its entire 36 in width while staying outside the water opening. Both are measured design-sense targets awaiting exported-geometry verification; neither establishes structural or permit approval.

- **Structure and materials:** R4501.4/.6, APSP 5 structural/material sections, and applicable concrete design. A nominal 6 in shell is a modeling assumption, not an engineered minimum. The structural professional must design soil support, groundwater uplift, reinforcing, concrete strength, cover, joints, penetrations, bond beam, spa/feature walls and foundation connections. Show the adopted layer thicknesses accurately, and mark them provisional. Paver and coping thickness depend on a selected product and installation assembly, not a universal Florida number.
- **Flood/groundwater:** Confirm survey elevations, flood/coastal designation, groundwater, finished equipment elevation and hydrostatic relief under R4501.4.2.1/.21.4 and R322. Florida high-groundwater conditions make a flat generic pad or empty-shell assumption insufficient. Sarasota's current guidance explicitly identifies R322.1.6 protection of mechanical/plumbing/electrical systems. [Sarasota County flood and building guidance](https://www.scgov.net/government/planning-and-development-services/building).
- **Hydraulics/PVC:** R4501.6.3/.6.5 and .20. Chapter 45 planning ceilings are 8 ft/s suction and 10 ft/s pressure, but adopted energy provisions and product instructions can be stricter; do not design merely to those ceilings. Confirm PHTA 15's applicable edition through Energy R403.12 and its referenced-standard chapter, then size every circuit using actual inside diameter, pipe length/fittings, elevation, total dynamic head and pump curves. Check pool/spa/feature combinations, maximum speed, blocked outlets, filter capacity and at-most-12-hour pool turnover. No pump horsepower or fixed PVC diameter is approved by a generic mesh. The 2023 energy errata material flags the APSP/PHTA name and 2021 reference discrepancy, so the pipeline must resolve it explicitly. [Commission energy errata](https://www.floridabuilding.org/fbc/thecode/2023_Code_Development/Glitch2-2023/Energy_TAC.pdf).
- **Installation/pressure testing:** R4501.12.1 calls for at least 35 psi for 15 minutes, witnessed/documented under the AHJ's accepted procedure. Use manufacturer-compatible materials and a safe test method; do not infer a field test from a digital model. [Village of Estero 2023-code pressure-test affidavit](https://estero-fl.gov/wp-content/uploads/library-ada/Community%20Development%20Applications/Building%20Permit%20Applications/Miscellaneous/Pressure%20Test%20Affidavit.pdf).
- **Equipment clearance:** R4501.22/.23 require manufacturer-compliant foundations and service access. Reserve actual filter removal height, heater airflow, pump access, electrical working space and anchorage. Example Pentair instructions require a 5 ft pool-wall offset and recommend a straight suction approach five pipe diameters long; these are product-specific, not a substitute for the eventual SKU schedule. [Pentair WhisperFlo instructions](https://www.pentair.com/content/dam/extranet/nam/pentair-pool/residential/pumps/whisperflo/manuals/whisperflo-pump-manual-english-spanish.pdf).
- **Electrical:** R4501.16 / 2020 NEC Article 680. Obtain circuit/load schedule, GFCI protection, grounding and equipotential bonding design (680.26), listed luminaires/transformers/junction boxes, controls/disconnects, receptacle locations, and overhead/underground utility clearances. Finish all required inspections before filling. The model's colored tubes or metallic rail appearance do not verify electrical safety.
- **Energy/heating:** Energy R403.10.1-.5/.12: document accessible heater on/off control separate from breaker, scheduling, required heat-loss control or substantiated exception, gas efficiency and heat-pump performance. The planning values in the prior direct-code review are gas efficiency 82% and heat-pump COP 4.0 at the specified low-air AHRI 1160 condition; the 2023 energy compliance form corroborates these. A heat pump's presence does not itself prove the greater-than-70% seasonal recovered-energy cover exception. A thermal cover is not automatically an ASTM safety cover. [2023 mandatory energy form, municipal permit record](https://pine-trk.aspgov.com/eTRAKiT/viewAttachment.aspx?ActivityNo=BL2024-0603&Group=PERMIT&key=EPRS%3A240731125913816).
- **Site/deck:** Survey, easements, setbacks, excavation access, neighboring foundations, utilities, drainage discharge, actual deck grading, wet slip resistance, accessible customer needs and local rules remain open. Avoid applying public-pool deck-width rules indiscriminately. Keep actual unobstructed routes clear of lounge furniture, pool steps, spa approaches and pergola posts. Plumbing fill/backflow and waste/discharge design require R4501.9/.10/.13 review.

## Per-design screening list

All 20: complete stair flight, actual water depth, complete barrier, service route, listed equipment gate, net volume and exact material-scale checks. “Minimum required returns” is the geometric screening count; additional returns may improve circulation and do not remove the spacing review.

| ID | Design | Main-pool area sq ft | Minimum required returns | Extra review |
|---|---|---:|---:|---|
| 101 | Lanai Classic | 288.0 | 1 | Screen/house barrier connection |
| 102 | Sun Shelf 26 | 312.0 | 2 | Shelf-to-floor stairs; screen |
| 103 | Courtyard Dip | 196.5 | 1 | Tight curved stairs, shelf and lounge route |
| 104 | Family Thirty | 420.0 | 2 | Full-width shelf entry; screen |
| 105 | Palm Curve | 319.2 | 2 | Clipped stair/bench width; screen |
| 106 | Coastal Kidney | 314.1 | 2 | Return circulation around waist; screen |
| 107 | Weekend Retreat | 392.0 | 2 | Shelf entry and open-yard barrier |
| 108 | Morning Laps | 360.0 | 2 | Preserve usable swimming lane |
| 109 | Roman Garden | 349.5 | 2 | Usable treads within curved end; screen |
| 110 | Spa Side | 288.0 | 1 | Spa approach, coping junction, screen |
| 111 | Suncoast Social | 450.0 | 2 | Full-width shelf, spa approach, screen |
| 112 | Two Lounger Retreat | 420.0 | 2 | Loungers must not occupy clear entry route |
| 113 | Tropical Cove | 390.9 | 2 | Curved shelf, round-spa footwell, cascade suction |
| 114 | Waterwall Court | 392.0 | 2 | Waterwall foundation/circuits; spa approach |
| 115 | Courtyard L | 400.0 | 2 | Circulation/egress in both legs; concave offsets |
| 116 | Sunset Baja | 512.0 | 2 | Full-width shelf, spa access, pergola supports |
| 117 | Resort Lane | 480.0 | 2 | Side-shelf lane clearance, side spa, pergola |
| 118 | Arc and Stone | 417.0 | 2 | Curved stairs, round spa, waterwall |
| 119 | Bayline Edge | 576.0 | 2 | Engineered weir/catch basin, fall/barrier strategy |
| 120 | Island Lounge | 516.0 | 2 | Peninsula route, both U legs, corners and circulation |

## Design-process vulnerabilities and controls

1. **Edition ambiguity:** A document date is not a code edition. The Nassau County September 2025 application identifies current 2023 code on page 2 but appends 2020 code pages at pages 21-23. Store source edition, printing, retrieval date, section and applicability separately. Do not trust a current-looking title alone. [Nassau County packet](https://www.nassaucountyfl.com/DocumentCenter/View/26116/Swimming-Pool--Pool-Enclosure-Application-092025?bidId=).
2. **AI image/model divergence:** Derive final photorealistic renders from the audited geometry. A generated lifestyle image is an appearance concept, not proof of pool outline, step positions, equipment or scale.
3. **Symbol-to-approval confusion:** Generic drains, pumps, screen members, shell and pipe meshes must remain “selection/engineering pending” until matched to approved schedules. A mesh named “drain” does not prove an installed suction assembly.
4. **Dimension drift:** Use a single coordinate and unit convention, independent exported-mesh measurements, and a test of the final stair-to-floor drop. Check polygon validity, actual thickness, overlaps, clear passages and net material volumes. Recompute estimates after geometry changes.
5. **Print/detail distortion:** Keep full-scale design geometry separate from fabrication accommodations such as thicker rails, legible labels, supports and print base. Record every display-only enlargement. Raised branding belongs to a model presentation layer; it must not silently become an actual trip/abrasion feature on the pool floor or walking surface.
6. **False completed status:** Use separate evidence fields for `geometryChecked`, `printMeshChecked`, `physicalPrintTested`, `renderMatchesModel`, `engineeringApproved`, `permitApproved` and `fieldInspected`. No one boolean should imply all seven.
7. **Suction and energy omissions:** Require pump-mode matrix, listed cover/sump record and hydraulic/energy calculation before a construction release. Do not calculate from bounding rectangles, nominal pipe IDs or normal-speed-only flow.
8. **Stale duplicate assets:** The old collection's passing tests and print kits belong to its own edition. Tie every export, render, estimate and print pack to the active design ID, edition and source hash.

Recommended release wording: **“Measured residential design concepts with documented design checks and printable display models. Property-specific engineering, product selection, permits and inspections are required before construction.”**
